![winchester m14 rail mount winchester m14 rail mount](https://hardairmagazine.com/wp-content/uploads/2016/02/M14-Scope-Mounts-HAM.jpg)
The groove with a dial caliper or depth micrometer using the probeįunction in the normal manner. 2 is the groove depth and is found by measuring the depth of The total thickness of the receiver width with the pin in the groove.ĭim. The appropriate-sized and secured pin height above the left surface.įind this by measuring the receiver width and then subtracting that from 1 is the groove width, which is the same as With the correct pin chosen, there are four important dimensions The pin is not in contact with the bottom of the groove and is the Pull the paper strip out from under the secured pin, you'll know With rubber bands on top of the paper strip in the groove. Groove bottom and allowing for a tab for grasping. Cut a strip of paper no wider than the width of the The first step is to identify which of the two inspection pins bestįits your receiver. Kit, you'll need an accurate measuring tool, such as a six-inchĭial caliper (good) or a two-inch micrometer (best). The groove has tapered side walls and must be measured over a round The large pin measures 0.1563 and the small pin To inspect the receiver to determine if the left side groove is within This inspection kit consists of a set of precision-ground pins used Will determine specific dimensions and confirm if the mount is correctly Is experiencing windage or elevation problems, a receiver inspection Problems due to an out-of-spec receiver groove. Receiver groove inspection kit to help troubleshoot scope mounting Inspected due to a number variations in manufacture. Only two hex wrenches are required to service the mount.īefore installing on a given M14/M1 A, the receiver must be Of the receiver for greater contact surface with the receiver. The third contact point (from 1/4-28 to 5/16-24) contacts the top front SADLAK'sĪdditional clearance helps alleviate this.Īdded semi-circle notches on either side of the mount allows theĬlip guide key to be tightened in the receiver groove while the mount isĪttached for more convenient installation. The spent case can be thrown vertically and hit the mount. Underside allows spent cartridges to better clear. Socket head cap screw for secure holding as with the Brookfield design,Īn added five-degree case deflection angle on the mount's Rather then depend exclusively on a small #10
![winchester m14 rail mount winchester m14 rail mount](https://i.ytimg.com/vi/qHeugLehhJY/maxresdefault.jpg)
Without sacrificing holding power and allows the screw to better mate up With the clip guide key securely wedged and locked into theĭovetail groove, the elongated slotted hole allows more adjustability Which is more secure than the Brookfield design and offers a betterĪnchoring point for the mount at the stripper clip guide area that isīetter able to withstand the recoil forces without loosening. The key acts as an immobile stationary nut,
![winchester m14 rail mount winchester m14 rail mount](https://airgunmaniac.com/wp-content/uploads/2020/03/Winchester-M14-CO2-Trigger.jpg)
The dovetail groove of the stripper clip guide for maximum surfaceĬontact and holding power. The outboard setscrews wedge the key into When Brook-fieldĬeased operations in the mid-1990s, Mike Sadlak offered his own designįirst was the increased length and addition of two outboard set Improvement over the original aluminum military mounts. Commonly knownĪs a three-point contact M14 scope mount, the Brookfield was an Original designer and manufacturer of this type of mount. Prior to SADLAK's design, Brook-field Precision Tool was the Two primary product lines, one in the AR market featuring their gasīlocks and the other for M14/M1A rifles featuring their Premium Scope As his company grew, he sought out new opportunitiesĪnd began looking into components for firearms. Mike Sadlak started in the industry in 1989 as Sadlak Innovativeĭesign, an engineering studio developing solutions for manufacturing andĪssembly companies. Released a generation before this trend, SADLAK Industries (, While classic self-loading military rifles such as the M14/M1A were Optics are becoming increasingly more common on military rifles.
#WINCHESTER M14 RAIL MOUNT FREE#
MLA style: "SADLAK Scope Mount: SADLAK's scope mount is an ideal way to add optics to M14/M1A rifles." The Free Library.